Using the software DV3 ... I have a issue I describe:
I have 4 scanner (Golden Scan 3 of Clay Paky) and create a scene with: iris open, yellow and diffuse brightness of dmx dimmer value to 0 (light off).
I select all 4 scanners and increase the brightness with the slider 4 bringing the value of the dmx from 0 to 130, the scanner will turn on all 4 on the yellow light as set on the scene.
A the point i unselect the 3 scanner, and i change the size of iris on the only scanner i have selected, but when i unselect the 3 scanner, they turn off while i want that they remain lit how i had setted last time.
How do I fix it?
Have a Problem :?
For first thank for interest and reply SimonB
I try of clarification this situation:
- I have four scanner Golden scan 3 of Clay Paky and the start address of each scanner are: the first has address dmx 1 to 8 the second 21 to 28 the 3° 41 to 48 and the 4° 61 to 68.
For each single adress have this function:
Address 1-21-41-61: Command Iris level 1 to 255
Address 2-22-42-62: Change color level 1 to 255
Address 3-23-43-63: Effect level 1 to 255
Address 4-24-44-64: Light level 1 to 255
Address 5-25-45-65: Pan level 1 to 255
Address 6-26-46-66: Tilt level 1 to 255
Address 7-27-47-67: Gobos level 1 to 255
Address 8-28-48-68: RotoGobo level 1 to 255
In to window Golden scan 3, i have four buttom where i select or unselect the scanner that i want change the color, the effect ecc.
When i active an scene, i want have the possibility of unselect the scanner, that i have set right and i use only one for do another function.
The scene saved, the light for all scanner are at 0 ( adress 4-24-44-64 level 0).
When i recall the scena and i bring the level of adresse 4-24-44-64 to 130 , and in this moment unselect the scanner 1 and 2 and 3, they turn off.
I hope i explained well, if not, i'm at disposition
I try of clarification this situation:
- I have four scanner Golden scan 3 of Clay Paky and the start address of each scanner are: the first has address dmx 1 to 8 the second 21 to 28 the 3° 41 to 48 and the 4° 61 to 68.
For each single adress have this function:
Address 1-21-41-61: Command Iris level 1 to 255
Address 2-22-42-62: Change color level 1 to 255
Address 3-23-43-63: Effect level 1 to 255
Address 4-24-44-64: Light level 1 to 255
Address 5-25-45-65: Pan level 1 to 255
Address 6-26-46-66: Tilt level 1 to 255
Address 7-27-47-67: Gobos level 1 to 255
Address 8-28-48-68: RotoGobo level 1 to 255
In to window Golden scan 3, i have four buttom where i select or unselect the scanner that i want change the color, the effect ecc.
When i active an scene, i want have the possibility of unselect the scanner, that i have set right and i use only one for do another function.
The scene saved, the light for all scanner are at 0 ( adress 4-24-44-64 level 0).
When i recall the scena and i bring the level of adresse 4-24-44-64 to 130 , and in this moment unselect the scanner 1 and 2 and 3, they turn off.
I hope i explained well, if not, i'm at disposition