Is there a USB Board than can be used with the software?
-
- Posts: 76
- Joined: Mon Feb 23, 2009 10:04 pm
- Contact:
Is there a USB Board than can be used with the software?
I have seen LDs that use a laptop and software setup but also have a small board hooked to the laptop. Can any one recommend the best one for this software?
Thanks,
J. Gibson
Thanks,
J. Gibson
-
- Posts: 76
- Joined: Mon Feb 23, 2009 10:04 pm
- Contact:
AoS Lighting wrote:I have the DVC2 512 interface, I was wondering if there is an external board that can be used with the software?
Thanks
If it's an interface then only the USB interfaces are available for DVC2, I think there used to be a bare board version but it was still a USB.
If you mean an external control surface with sliders etc, then you can use a DMX lighting desk and have that as an "IN" device controlling DVC2, or it could be a midi device such as the Behringer BCF2000, which works well apparently.
There is no specifically designed hardware controller for DVC2.
Andre
-
- Posts: 76
- Joined: Mon Feb 23, 2009 10:04 pm
- Contact:
AoS Lighting wrote:If you mean an external control surface with sliders etc, then you can use a DMX lighting desk and have that as an "IN" device controlling DVC2, or it could be a midi device such as the Behringer BCF2000, which works well apparently.
There is no specifically designed hardware controller for DVC2.
Ok, Thanks
-
- Posts: 76
- Joined: Mon Feb 23, 2009 10:04 pm
- Contact:
[/quote]or it could be a midi device such as the Behringer BCF2000, which works well apparently.[/quote]
Hi again. Sorry it has been forever on this post. But how would I connect the BCF2000? Just use another usb port? (I will have the DVC2 512 interface plugged into one usb port). And I can assign faders from the software to faders on the BCF2000?
Thanks!
Hi again. Sorry it has been forever on this post. But how would I connect the BCF2000? Just use another usb port? (I will have the DVC2 512 interface plugged into one usb port). And I can assign faders from the software to faders on the BCF2000?
Thanks!
-
- Posts: 463
- Joined: Fri Jul 11, 2008 10:30 am
- Location: Orlando. Florida
- Contact:
yes the BCF is connected by usb before you start DVC.
The control is limited but might be good for your situation.
you can assign dimmer faders to individual channels or even F groups of channels.
Howebver once assigned the channel can only be used by the BCF and the software can no longer control the channel. which might be ok for your application.
You can also trigger on/off scenes with the BCF buttons. which is useful. Additionally you can control pause and some other live functions.
The control is limited but might be good for your situation.
you can assign dimmer faders to individual channels or even F groups of channels.
Howebver once assigned the channel can only be used by the BCF and the software can no longer control the channel. which might be ok for your application.
You can also trigger on/off scenes with the BCF buttons. which is useful. Additionally you can control pause and some other live functions.
Music sets the mood Lighting sets the ambience
-
- Posts: 76
- Joined: Mon Feb 23, 2009 10:04 pm
- Contact:
-
- Posts: 76
- Joined: Mon Feb 23, 2009 10:04 pm
- Contact:
Another quick question.. I only have two usb ports on my laptop. I usually plug the DVC interface into one and a mouse in the other. Will the BCF work if I use a usb splitter and split it with the mouse? I tried to split the mouse and the DVC interface. All the lights on the interface were on and it seemed like it was working fine, but I had no control over the lights (so I guess the interface won't work with a usb splitter?)
Is there another option than a splitter? Or is there a specific kind of usb splitter I would need to use for it to work?
Thanks for your help.
Is there another option than a splitter? Or is there a specific kind of usb splitter I would need to use for it to work?
Thanks for your help.
-
- Posts: 463
- Joined: Fri Jul 11, 2008 10:30 am
- Location: Orlando. Florida
- Contact: