Virtual Controller 2 Bugs
Virtual Controller 2 Bugs
Please submit any bugs you find in the software here
-
- Posts: 101
- Joined: Fri Feb 15, 2008 3:07 pm
- Contact:
Bug: DaslightRemoteControl.dll cannot be used by external apps.
I've tried accessing it through both dynamic and static linkage from Visual C++, and also using JNA under Netbeans Java. In all cases, under both Windows XP and Vista 32, the functions in the library return failure codes.
I've tried accessing it through both dynamic and static linkage from Visual C++, and also using JNA under Netbeans Java. In all cases, under both Windows XP and Vista 32, the functions in the library return failure codes.
A lie goes half way around the world before the truth gets its pants on.
Bug: Stand Alone Read Memory Button
The "Write the Interface Stand Alone Memory" button on the "Stand Alone Memory Map" works and writes files to the GZM Interface's Memory (i.e. Mini SD Card). The LED read "A01. A02, ...."
After exiting the Stand Alone Mode and the returning to it, the "Memory Read" button function in the "Stand Alone Memory Map" screen does not read the scenes stored in my GZM Interface's Memory Upon pressing the "Memory Read" button nothing appears in the blocks of the Stand Alone Memory Map."
Pressing the "Memory Read" button appears to have the effect of deleting the scenes just like the "Erase Memory" button. After pressing the "Memory Read" button; disconnecting the GZM Interface from the Computer and connecting the GZM Interface to the Power Cable the GZM Interface LED display reads "OFF" instead of "A01, A02, ...," The GZM Interface will not play scenes in the Stand Alone mode, unless I again connect the computer to the Interface, process the scenes to the "Stand Alone Memory Map" and press the "Write the Interface Stand Alone Memory" button and proceed to the Stand-Alone mode without pressing the "Memory Read" button.
Since the only way to retrieve, or obtain information about the scenes stored on the GZM Interface's Memory is the "Memory Read" button, a functioning "Memory Read" button would be appreciated.
The User's Manual says at page 41, "Don't loose the previous content of your memory if you need it." The memory content is needed to run the scenes; and as additional Mini SD Cards are created for different shows, the "Memory Read" feature will be needed to identify/verify the scenes stored in the GZM Interface memory which may consists of multiple Mini SD Cards.
Thank you for your attention to this issue.
After exiting the Stand Alone Mode and the returning to it, the "Memory Read" button function in the "Stand Alone Memory Map" screen does not read the scenes stored in my GZM Interface's Memory Upon pressing the "Memory Read" button nothing appears in the blocks of the Stand Alone Memory Map."
Pressing the "Memory Read" button appears to have the effect of deleting the scenes just like the "Erase Memory" button. After pressing the "Memory Read" button; disconnecting the GZM Interface from the Computer and connecting the GZM Interface to the Power Cable the GZM Interface LED display reads "OFF" instead of "A01, A02, ...," The GZM Interface will not play scenes in the Stand Alone mode, unless I again connect the computer to the Interface, process the scenes to the "Stand Alone Memory Map" and press the "Write the Interface Stand Alone Memory" button and proceed to the Stand-Alone mode without pressing the "Memory Read" button.
Since the only way to retrieve, or obtain information about the scenes stored on the GZM Interface's Memory is the "Memory Read" button, a functioning "Memory Read" button would be appreciated.
The User's Manual says at page 41, "Don't loose the previous content of your memory if you need it." The memory content is needed to run the scenes; and as additional Mini SD Cards are created for different shows, the "Memory Read" feature will be needed to identify/verify the scenes stored in the GZM Interface memory which may consists of multiple Mini SD Cards.
Thank you for your attention to this issue.
-
- Posts: 101
- Joined: Fri Feb 15, 2008 3:07 pm
- Contact:
System: Windows 7 / 64-bit on Acer Laptop 4GB RAM
Daslight version: 12/09
DMX Interface: ECO 512, disconnected (may be irrelevant)
Description: error dialog on exit
Reproduction: start Daslight, load a project, change a few things, exit.
Symptom: after Daslight closes, Windows raises a software failure dialog.
Daslight version: 12/09
DMX Interface: ECO 512, disconnected (may be irrelevant)
Description: error dialog on exit
Reproduction: start Daslight, load a project, change a few things, exit.
Symptom: after Daslight closes, Windows raises a software failure dialog.
A lie goes half way around the world before the truth gets its pants on.
-
- Posts: 101
- Joined: Fri Feb 15, 2008 3:07 pm
- Contact:
Can't drag scenes upwards properly in Editor
System: Windows 7 / 64-bit on Acer Laptop 4GB RAM
Daslight version: 12/09
DMX Interface: irrelevant
Description: a scene cannot be dragged upwards past the visible top of the scene list
Reproduction:
* create a few groups
* create as many scenes in edit mode as it takes to fill more than one screen, entered in the groups you created
* scroll to the end and create a new scene at the bottom
* try to drag the new scene to the very top of the list
Symptom: the new scene cannot be dragged past the first visible scene at the top - the list should scroll down so you can insert the scene anywhere
Daslight version: 12/09
DMX Interface: irrelevant
Description: a scene cannot be dragged upwards past the visible top of the scene list
Reproduction:
* create a few groups
* create as many scenes in edit mode as it takes to fill more than one screen, entered in the groups you created
* scroll to the end and create a new scene at the bottom
* try to drag the new scene to the very top of the list
Symptom: the new scene cannot be dragged past the first visible scene at the top - the list should scroll down so you can insert the scene anywhere
A lie goes half way around the world before the truth gets its pants on.
-
- Posts: 101
- Joined: Fri Feb 15, 2008 3:07 pm
- Contact:
3D viewer does not save object scaling
System: Windows 7 / 64-bit on Acer Laptop 4GB RAM
Daslight version: 12/09
DMX Interface: ECO 512, disconnected (may be irrelevant)
Description: The 3D viewer doesn't save scaling values
Reproduction:
* start Daslight, load a project, start the 3D viewer.
* in construction mode, load an object in the viewer (I used an amplifier)
* select the scale tab, and enter values in the % fields (I used 80)
* save the scene
* close the viewer
* re-start the viewer, and re-load the saved scene
Symptom: the amplifier's scale has returned to 100%.
Daslight version: 12/09
DMX Interface: ECO 512, disconnected (may be irrelevant)
Description: The 3D viewer doesn't save scaling values
Reproduction:
* start Daslight, load a project, start the 3D viewer.
* in construction mode, load an object in the viewer (I used an amplifier)
* select the scale tab, and enter values in the % fields (I used 80)
* save the scene
* close the viewer
* re-start the viewer, and re-load the saved scene
Symptom: the amplifier's scale has returned to 100%.
A lie goes half way around the world before the truth gets its pants on.
Re: Can't drag scenes upwards properly in Editor
smokeAndMirrors wrote:System: Windows 7 / 64-bit on Acer Laptop 4GB RAM
Daslight version: 12/09
DMX Interface: irrelevant
Description: a scene cannot be dragged upwards past the visible top of the scene list
Reproduction:
* create a few groups
* create as many scenes in edit mode as it takes to fill more than one screen, entered in the groups you created
* scroll to the end and create a new scene at the bottom
* try to drag the new scene to the very top of the list
Symptom: the new scene cannot be dragged past the first visible scene at the top - the list should scroll down so you can insert the scene anywhere
I am pretty sure it has been like it for a long time. I always had to drag top item down to get the one below to be the top item.
You have always had to scroll the list manually to get room to drag the scene up again.
Yes it would be good if it could be fixed.
Andre
-
- Posts: 101
- Joined: Fri Feb 15, 2008 3:07 pm
- Contact:
Scene copy is shallow
When copying and pasting a scene in edit mode, not all the traits are duplicated. Eg if I copy a scene with a jump, the cloned scene will not have a jump. The same goes for the release setting. The copy should either replicate the fields, or there should be an additional "smart copy" that allows you to choose the fields to duplicate.
A lie goes half way around the world before the truth gets its pants on.
Re: Scene copy is shallow
smokeAndMirrors wrote:When copying and pasting a scene in edit mode, not all the traits are duplicated. Eg if I copy a scene with a jump, the cloned scene will not have a jump. The same goes for the release setting. The copy should either replicate the fields, or there should be an additional "smart copy" that allows you to choose the fields to duplicate.
Yep found that one, been like that for a longtime though.
The new scene thing is a pain in the a$$ always at bottom of list.
Andre
-
- Posts: 101
- Joined: Fri Feb 15, 2008 3:07 pm
- Contact:
New scenes appear in the wrong place
When you create a new scene in edit mode, and there is a currently selected scene, the new scene should appear immediately after that scene. As it stands it appears at the end of the current group, which often forces a disorienting scroll of the screen.
A lie goes half way around the world before the truth gets its pants on.